Česky English Pусски Po polsku Deutsch
manufacturer of industrial valves

Vertical lift-type check valve with automatic relief KM 9903.1 117 (Z40)

Products >> Vertical lift-type check valves

DN 50 – DN 400, PN 16 – PN 100

Datasheets for download


Flanged vertical lift-type check valve with automatic relief type KM 9903.1 117 (Z40) is designed to ensure safety of service, i.e. to protect pump against reverse flow of the pumped fluid and to safe start-up and termination of operation of the pump. The valve is not designed for long-term fluid flow through the bypass when the bypass channel is opened.

The check valve for vertical pipeline is an unidirectional valve and the direction of the fluid flow is marked with an arrow on the valve's body from the bottom to the top, i. e. under the disc. In case the fluid starts flowing back, the disc closes the check valve automatically. Movement of the disc is linked with movement of the piston of automatic relief which opens the flow to the bypass. The bypass is connected to a pipe which mouths into the pump tank. In this way the pump can terminate its operation with a minimum quantity of the fluid in order to protect it against damage by overloading. Closing or opening of the bypass channel is not mechanically regulated. Operation of the valve with opened bypass channel is accompanied by increased noise. When the valve is opened then the bypass channel is closed by a piston which is loose in its bush therefore it is not possible to ensure 100% tightness of the inlet of the bypass channel.

Vertical lift-type check valves are neither designed as conventional isolating valves nor regulating valves. If permanent tightness of the disc or bypass is required, an isolating valve shall be installed into the delivery piping or bypass piping. The service fluid must contain no mechanical impurities in form of grains or powders and its chemical composition must not form segregation deposits on the piston and the piston guide bearings. The same applies to impurities in the piping system during installations, repairs or replacements.

The check valves are designed to be used with fluids in group 2 (non-corrosive fluids with the exception of potable water) according to Decree of the Government No. 26/2003 and Pressure Equipment Directive 97/23/EC, but it is recommended to use this valve for demineralized water only. The resistance of the check valve to the fluid and its temperature is limited by the chemical composition of the check valve materials. It is therefore recommended to consult the suitability for the relevant fluid with the manufacturer. Allowable service pressures are in compliance with the pressure-temperature ratings.

Technical description

The main part of the flanged vertical lift-type check valve with automatic relief is a one-piece body which is made of rolled or forged steel. The body contains an inlet disc guide and an outlet disc guide with plain bearings and a piston guide with bronze bushing which are pressed into the body. The pressed-in parts are secured by centre punching or welds. The disc guides are secured in place by the counter-flanges of the piping. The seats of both the body and the disc are usually weld-deposited with austenitic steel of 18/8 CrNi type or Stellite 6 – type of the weld overlay depends on the material composition of the check valve. The disc is lapped with the body seat.

The disc closes by self-weight and, in addition to it, is pressed into the seat by a compression spring made of a high-quality material. The piston, which is linked to the spindle of the disc, moves with the disc and automatically opens or closes the fluid flow to the bypass. The pressure drop on the bypass channel is reduced on a single orifice plate or a set of orifice plates. It is recommended to the user to install a horizontal pipeline behind the flange of the bypass with its length at least 5 times of the nominal diameter of the bypass pipeline, to soothe the turbulent flow of the fluid.

The design of the valve is suitable for pressures up to PN 100 and for a maximum volume flow rate through the bypass channel of about 20 % of the allowed volume flow rate through the check valve.

Connection to piping

Overall dimensions are shown in the datasheet. Dimensions according to standards:

  • connection according to EN 1092–1
  • face-to-face dimensions in pressure classes PN 16, 25, 40 – Series 1 according to EN 558–1
  • face-to-face dimensions in pressure classes PN 63, 100 – Series 2 according to EN 558–1


According to EN 12 266–1 as a standard, i.e. shell strength test P10, P11, seat tightness test P12 (water pressure 1,1×PN and air pressure 0,6 MPa), leakage rate A – zero leakage, operability test F20. Standard ČSN EN 13709 specifies that a seat leakage corresponding to leakage rate C according to ČSN EN 12266–1 is allowed in case of test P12. If required by the Customer, additional tests may be performed as well.

Installation, service and maintenance

Vertical lift-type check valve shall be installed in vertical position. As it is a uni-directional valve, the fluid flow shall correspond to the arrow marked on the valve body. When installing the vertical lift-type check valve to piping it should be taken into account the fact that that in the fully open position of the valve the shaft of cone protrudes above the outlet flange by a distance which is equal to the maximum cone lift.

If the values of temperature and pressure of the fluid and quantity of the fluid flowing through the branch piece as specified on the valve label are adhered to, the check valve operation is fully automatic.

When the service fluid does not meet the requirements regarding the purity, the operator must ensure regular cleaning of the piston and of the bronze piston guide otherwise the piston gets blocked. Cleaning interval depends on the specific operating conditions, however, it is recommended to clean the piston guide every 2 months.

Ball valves|Three-way valves|

Check valves|Services


Pekařská 1639/79A, Opava
Czech Republic

+420 555 440 200


Privacy Policy

© 2003-2020 KE-ARM, s.r.o.